The CAL 76 Relay Circuit Pro can test an entire circuit from the battery to the component in question as well as determining if the relay itself is functioning properly.
Relay Circuit Pro will identify at the push of a button if a wire a part or a relay is defective without the use of a multi-meter.
For additional testing use the ports on the CAL 76 to connect to other diagnostic tools. Since the CAL 76 can jump, use it as a remote control starter in engine work like compression testing distributor or cam shaft adjusting or to run the compressor during an A-C charge.
Works with both 12 and 24 volt systems.
Contents
• CAL-76 units
• 6 relay leads
• Universal relay lead
• Manual
• Blow molded case with a high density foam insert
• 1-year warranty
Watch Video Here.https://youtu.be/lIgqEMtnHIA
Great for activating circuits while performing current draw testing
Related Products
TDB003 Smart Key Tester
The TDB003 Proximity/Smart Key Systems Tester offers a simple and cost effective way to diagnose and test problems relating to the vehicle immobiliser system, which is made up of a number of components.
The TDB003 enables the transponder key, remote control operation, external vehicle antenna transmitters, internal vehicle antenna transmitters and transponder antenna to be fully tested to ensure that all parts of the system are working.
The TDB003 can display signal levels, frequency measurements, signal waveforms and
a number of other useful features.
U-Scope Basic Kit with Test Leads
$395.93
U-Scope Basic Kit with Test Leads
$395.93
$395.93Add to cart
U-Scope Basic Kit with Test Leads
The uScope: Small enough to fit in your pocket and powerful enough to capture the fastest signals, in less than 4 seconds it’s booted up and ready to take aim on any signal.
The uScope is equipped with a 12-bit analog/digital converter, samples at 1 million/second and includes 10x peak detect oversample.
Coil On Plug Inductive Signal Probe
$366.18
Coil On Plug Inductive Signal Probe
$366.18
$366.18Add to cart
Coil On Plug Inductive Signal Probe
Coil On Plug (COP) and Signal Probe
The TA204 COP and signal probe from Pico Technology is the easiest and fastest non-intrusive way to check coil-on-plug ignition coils and spark plugs.
- Find misfires fast
- Displays scope patterns of the secondary, faster than scoping the primary
- Works on all automotive scopes capable of displaying ignition patterns
- Can also be used to investigate injectors and other inductive actuators
- Flexible design allows for easier access to hard-to-reach components
- No batteries required
Like distributors, spark plug wires are starting to disappear from cars. With the new COP ignition systems the ignition coils are connected directly to the spark plugs — eliminating the need for the spark plug wires. With no high-voltage spark wires, a COP probe is required to be able to pick up the secondary ignition waveform.
As standard the TA204 COP probe is supplied as a kit (PP357) complete with the TA033 BNC to BNC cable in order to connect to your automotive
How does it work?
The coil–on–plug and signal probe works with most COP systems; it requires no special adaptors, no foil strips, and no batteries. The Pico coil-on-plug and signal probe eliminates the need for back-probing: to use the probe simply press the probe against the coil.
Along with testing COP systems, the coil-on-plug and signal probe can also be used to obtain many other signals, including a secondary ignition waveform on conventional ignition systems.
Designed to save you time, effort and money, the coil-on-plug and signal probe is the fastest way to test both conventional coil-on-plug secondary ignition systems.
EsiTest #180 LOADpro Dynamic Test Leads
$123.45
EsiTest #180 LOADpro Dynamic Test Leads
$123.45
$123.45Add to cart
EsiTest #180 LOADpro Dynamic Test Leads
LOADpro finds these problems FAST: High Corrosive Resistance Shorts to Ground Open Circuits LOADpro Test Leads load the circuit to see if
AES Wave Breakout Box
We call it the AES LineSpi SMART BOB.
The AES LineSpi SMART BOB is a pass-through breakout box for the OBDII DLC (diagnostic link connector).
It’s a DLC magnifier: makes the DLC 5-times larger.
It’s a DLC extender: puts the DLC where you need it.
It’s a spy: exposes the activity on each OBD-II dedicated dataline.
Yes, you still have to locate the vehicle’s DLC and attach the LineSPI SMART BOB but after that everything is so much easier:
