The CAL 76 Relay Circuit Pro can test an entire circuit from the battery to the component in question as well as determining if the relay itself is functioning properly.
Relay Circuit Pro will identify at the push of a button if a wire a part or a relay is defective without the use of a multi-meter.
For additional testing use the ports on the CAL 76 to connect to other diagnostic tools. Since the CAL 76 can jump, use it as a remote control starter in engine work like compression testing distributor or cam shaft adjusting or to run the compressor during an A-C charge.
Works with both 12 and 24 volt systems.
Contents
• CAL-76 units
• 6 relay leads
• Universal relay lead
• Manual
• Blow molded case with a high density foam insert
• 1-year warranty
Watch Video Here.https://youtu.be/lIgqEMtnHIA
Great for activating circuits while performing current draw testing
Related Products
Test Lead Set of 4 for Snap On Scopes
$196.19
Test Lead Set of 4 for Snap On Scopes
$196.19
$196.19Add to cart
Test Lead Set of 4 for Snap On Scopes
Snap On Lab Scopes are great tools but their lab scope test leads are too short for test drives. Plus, when using multiple channels, ground stacking becomes a problem. The ST3 Test Lead Kit for Snap-on VERUS solves these problems.
Advanced Terminal Leads Kit
This uTest Advanced Terminal Test Kit is the perfect companion for your lab scope and meter.
Includes Fuse Amp Loops with large loops and flexible wire for ease of connection and placement.
It includes 118 essential and common adapters, probes, and terminals that connect to a wide variety of sensors, actuators and circuits. Use with your lab scope or DMM. Use for terminal drag testing too.
A soft-sided carrying case keeps everything organized.
Specifications for variable resistor in kit: 10KΩ
9ft. Shielded Lead Set
ST3 Test Leads are designed to withstand automotive environments:
– Shielded from tip-to-tip for maximum noise immunity
– Heat resistant
– Flexible
– Small enough to easily pass under hoods and through windows for road testing.
Each lead is constructed using quality shielded cable and connectors. They are insulation and resistance tested to ensure that they are of the highest possible quality. Each test lead features high quality BNC connectors or banana-plugs. The test end features shrouded banana plugs that allow the use of a wide variety of probes such as pin tips, alligators, back-pin probes, piercing probes and more.
Piercing Probes Set of 5
Each piercer is just over 5-1/2 inches long and is designed to make test connections to wires of varying sizes (.050 to .150 diam).
The pointed tip allows separation of dense wire groups and easy connection.
The point is retracted by a syringe-type operation
No more “pulling back” on the handle to penetrate insulation.
The unit is molded in durable nylon, impervious to cleaning solvents and most fuels.
Set includes one probe of each color: Red, Blue, Yellow, Green, Black.
Screw Type Piercing Probes
Rotate the red or black jack to move the piercing needle forward into the insulation.
Rotating jack will not twist test lead while the needle is being screwed into wire.
* Can handle wires from 0.030″ diameter through 0.180″ diameter insulation.
* Overall length = 4-inches
* High visibility bright yellow body.
* Spring loaded slider holds wire centered for piercing needle.
* Mates with any banana plug test leads including the AES ST3 Test Leads.
* Mates with pin tip probe test leads. (see images below)
* Materials consist of a Nylon body, hardened steel needle, brass socket.
* Operating Voltage: 30VAC or 60V DC Max.
* Current: 1 Ampere Max.
Set includes two probes: one red, one black.
These Probes will connect to test leads that terminate to Shrouded, Standard and Retractable banana plugs.
